Frequently Asked Questions
How easy is it to install an efergy monitor?
The e2 couldn’t really be much simpler to install. Simply put the clamp onto the live mains cable in your fuse-box and put the display on your coffee table! Then program the display for your own requirements and that’s it!
How much money can I save with an efergy monitor?
The savings vary from user to user but they can be considerable, we reckon up to 20%, if you use an efergy monitor and change the way you use the electrical appliances around your home. We have put a guide together to show you how small changes can make a big difference!
How accurately are the monitors?
efergy monitors are accurate to within 10%, at least. In most cases they are accurate to within 5%. Most of this variation is due to fluctuations in your electricity supply. (The energy monitor is not intended to check the accuracy of your electricity meter, but to provide real time feedback to aid energy saving.) If however you are concerned about the safety of your electricity meter, please consult a qualified electrician.
Is the sensor supposed to be loose around the cable?
The sensor should fit loosely around your cable. Please do not pack it with anything to make it fit tighter. This could cause inaccurate readings and potentially be a safety hazard. If the sensor is too small for the cable you may need to purchase an XL sensor from our e-shop.
Can I compare the information displayed on my monitor to my electricity bill?
Our electricity monitors cannot be used as a comparison to your electricity meter, and to your electricity bill. Electricity meters have to conform to much stricter guidelines and testing procedures, which are not applicable to our range of wireless electricity receivers. All data displayed on our monitors should be for reference only.
What kind of information is displayed on the monitor?
All our monitors show power information (kW), cost information (£), and carbon emissions (CO2). The information is displayed in three different modes: instant, history and average. Press the top Function Button to change the information displayed from one mode to another.
Does the energy monitor need batteries?
Both the transmitter and the receivers work with 1.5v alkaline batteries and in addition the monitors can be powered by 6v DC adaptor to save on the use of batteries.
Are the monitors three phase compatible?
Yes. If you have a three phase supply, or economy 7 meter, then you may require additional sensors. These can be simply plugged into the additional sockets at the base of the transmitter.
What type of wireless communications do the monitors use?
Our transmitters use 433 MHZ to communicate with the display.
Which is the transmission rate?
Our transmitters send energy information data every 6s/12s/18s.
How far does the device transmit?
Transmitters work up to around 40-70 meters within the home. But this will depend upon the environment in which it is working. If the building that the monitor is operating in contains ironwork in the walls, thick concrete walls or floors and other wireless technology such as weather stations and wireless thermostats, then this can greatly reduce transmission ranges and possible cause the monitor to drop its link.
How much energy do efergy monitors consume?
Really low, less than 0.001 kWh.
With how much sensitivity is instant power displayed on the monitor?
All our monitors can display electricity consumption with a sensitivity of 1W.
How do our monitors work out what I am spending on electricity?
You will enter your tariff details from a recent bill onto the display so it can calculate the cost.
How long will the monitors record data for?
Our monitors can record data for the last 7 days, 7 weeks and 24 months (12 months for the elite monitor). They can also store hourly information for the last 240 days.
Will I lose the information in the event of a power cut or when I remove the batteries?
All information is stored in an internal memory which saves and holds the data even in case of power cut, or when you remove the batteries. In the event of a power cut the clock and the date will remain the same than when the power was removed. You will only loose the information stored in the memory when you reset the device.
If I remove the batteries will I lose the information on the display?
If you need to change or remove the batteries, the display has an internal memory, so information stored on the display will not be lost.
How long should the batteries last?
Battery life depends upon the quality and condition of batteries used, time spent interrogating the collected data and the intervals between transmissions. In ideal conditions up to 18 months of battery life can be expected in the products.
Can my energy monitor be used with economy-7 or dual timed tariffs?
Yes , the monitor can be used in conjunction with economy 7 and other timed tariffs. This is simple to set up in the menu when you enter the time, date, and tariff info. However the monitor cannot be precisely used with dual tariffs, where primary and secondary units are used. If this is the case averages of each set of units can be taken (based on previous bills). This will provide you with an overall average in pence per unit that can then be entered into the monitor.
How do i know what tariff to set in the menu?
Only your energy provider can supply these details. Please review your last bill or contact your provider.
I have four dashes (- - -) showing on the display. What does this mean?
Move the display closer to the transmitter and press the Link Button. If the dashes remain on the display this would indicate the transmitter and receiver are not communicating. Please contact efergy Customer Service to help locate the problem.
Backlight appears to work sometimes, and not other times. Is my display broken?
No. The backlight is on a timer to save battery life. The display should work at darker periods of the day, when any buttons are pressed. The LED backlight will be activated from 18:00Hrs to 6:00Hrs.
How do I reset the display (clear the data and start again)?
Only when is in the 'Energy Now' screen, push and hold for two seconds the buttons 'History' and Mode/Set until CLR appears on the screen. This will turn the display to his original setup (from factory) and should not affect neither time or date. Attention! You will lose all the information stored in the memory of the display.
What new features does the elink 2.2 bring?
The elink 2.2 brings a completely renewed look based in a cool blue colour background. The software includes three new interesting features:
- Historical and average demand curves: users can investigate daily historical as well as average daily (per week day and per month) demand curves.
- Add stickie feature: users can add text messages to every energy record. This will help track and follow up energy behavior in the home.
- Manage Demand Feature: the program shows the benefits of two possible shifts Tariff shift: it simulates the effect of moving from a single to dual tariff scheme, displaying the yearly benefits. Peak consumption shift: it simulates what would happen if demand peaks were to shift to off-peak periods (i.e. turning the tumble drier in an off-peak period), showing the yearly savings..
When I start the installation of the elink 2.2 I get an error message, what should I do?
Before installing the software ensure you have the latest version of Adobe air, Java, and .NET framework. Once you get these install the software choosing “Run as Administrator”.
I want to reinstall the the elink 2.2, how should I proceed?
In case you want to reinstall the software, first uninstall any previous versions of the elink software and any folders related to it, then you can proceed to reinstall the software.
I am using Windows Vista, is there any special installation requirement?
When running Windows Vista, make sure the User Access Control (UAC) feature is turned off before running this software. You must have Administrator privileges to proceed with the installation.
The elink 2.2 doesn't recognise when my efergy monitor is plugged into the computer. What happens?
The elink 2.2 might not recognise the monitor due to an installation failure. Please try again or reinstall the software.
Can I download the energy data from the elink software to an Excel spreadsheet?
Yes, you can. You just need to select Energy Report on the left-hand side of the elink window. Next select your dates to include in the report. Then click next. From the new screen you will be able to select save to computer which will create an excel and pdf file or you can select email report. Note that when you download daily report the information is stored in an hourly basis (one value per hour), and when you download the monthly report the information is stored on a daily basis (one value per day).
When i try to download my monitor information for second time it sends and error message or says that it cant find the device
When an USB enabled efergy monitor is connected to the computer the USB icon (on the display) comes ON and stays ON for some time, while is collecting the data from the monitor, After some time of being connected the monitor will start showing the 'Energy Now' or 'Instant screen' and you won’t be able to collect data. The data has to be collected when the USB icon is being displayed
Does the elink allow me to continuously collect energy data from the efergy monitor?
The efergy monitor cannot be left connected to the computer and collect data continuously. It has to be unplugged from the computer and reconnected to get new data. The device has to be disconnected and after 10-15 seconds should be reconnected back to computer to collect data.
Can I retrieve the energy data from the elink 1.0 and pass it to the elink 2.2?
You can transfer your data from elink 1.0 to elink 2.0 by using our elink converter. If you are upgrading to the elink 2.1/2.2 software you will need to send your current database to us for converting at firstname.lastname@example.org.
Is the elink 2.2 compatible with Mac OS?
Yes, you can download the Mac version of our software from our downloads section. Our elink 2.2 Mac version is compatible with the latest Mac OS Snow Leopard.
Is the elink 2.2 compatible with Windows 7?
elink 2.2 is compatible with Windows 7 (32 bit and 64 bit versions). Just ensure that the UAC is lowered to minimum, PC is restarted and the installation file is right clicked 'Run as Administrator' otherwise it won't link properly with the device.
Energy saving products
My remote control doesn’t respond to my remote controlled socket, what is the problem?
If your socket does not respond to the remote control please check the battery and replace iit if necessary. Get closer to the socket, since the distance between the remote control and the socket might be to great. Finally, ensure you are pressing the ON button on the remote for 1-2 seconds.
How can I decode my remote controlled socket?
To decode the device just press the ON/OFF button on the socket and hold for 3 seconds, the LED light will flash quickly and then it will stop. When so decoding is successful.
Can I decode with my remote control?
Yes, you can. To decode with the remote control press the OFF button and hold for 3 seconds, the LED light will flash quickly and then it will stop. Decoding is successful.
Is it possible to pause the showertime once it starts working?
Yes, it is possible in the new version of the showertime (which is now available) but unfortunately it is not possible in the older version. When you turn on the showertime it starts tracking your water consumption until you stop it. On the new version you just need to press the tick button to pause it and press tick button again to resume. On the older version if you want to start again measuring water consumption then the device will restart counting by reseting the previous value.